Skip to content

Miniature Planetary Gearbox Selector & Ratio Calculator (8–42 mm)

Start with a real SigGear Gearhead file or calculate a preliminary ratio. All 12 published sizes have direct engineering downloads. No registration is required; exact motor fit, rated loads and stage/ratio must still be checked for the selected configuration.

All 12 Models · PDF / 2D / STEP Motor Datasheet PDFs Existing Motor / Custom Interface Review

Browse by Diameter Before Ratio Selection

Published model Datasheet PDF 2D Outline Original Full Assembly STEP
8P · Ø8 mm PDF Datasheet 2D Drawing Full STEP
10P · Ø10 mm PDF Datasheet 2D Drawing Full STEP
12P · Ø12 mm PDF Datasheet 2D Drawing Full STEP
14P · Ø14 mm PDF Datasheet 2D Drawing Full STEP
16P · Ø16 mm PDF Datasheet 2D Drawing Full STEP
20P · Ø20 mm PDF Datasheet 2D Drawing Full STEP
22P · Ø22 mm PDF Datasheet 2D Drawing Full STEP
24P · Ø24 mm PDF Datasheet 2D Drawing Full STEP
28P · Ø28 mm PDF Datasheet 2D Drawing Full STEP
32P · Ø32 mm PDF Datasheet 2D Drawing Full STEP
36P · Ø36 mm PDF Datasheet 2D Drawing Full STEP
42P · Ø42 mm PDF Datasheet 2D Drawing Full STEP

Release scope: These are the published reference files, not approval for a particular motor input pinion, output loading, ratio or stage. The released 2D series uses stage-dependent body length; confirm the actual drawing revision and assembly envelope before production. File revisions and simplified STEP alternatives.

1. Decide What Needs to Be Supplied

Gearbox only: send your existing motor model/drawing, shaft, pilot, mounting geometry, loaded speed and target output.

Motor + gearbox assembly: send the available power supply, output speed/load, maximum diameter/length and duty cycle. SigGear can review a motor with a planetary gearbox as a matched assembly; no standard frame is guaranteed to fit a third-party motor automatically.

SigGear Planetary Gearbox Selector

Enter loaded motor operating rpm and required output rpm to compare published stages, ratios, gearhead body lengths and rated allowable torques. Optional diameter, length, continuous/peak load and ratio-difference filters narrow the initial shortlist.

Interpret the results carefully: Closest Ratio, Smallest Surviving Frame and Shortest Surviving Gearbox are different screening outcomes. A smaller or shorter unit is not necessarily better for torque, ratio or duty. The tool does not validate motor shaft compatibility, service life, peak duration or actual thermal behavior.

Input speed: permissible continuous speed is motor- and configuration-dependent. Use the selected motor and the model-specific verified specification; do not apply a universal continuous-speed cap to all 8P–42P gearheads.

Worked Example: From Motor Speed to a Published Gearbox Ratio

Preliminary reduction ratio ≈ motor speed at the loaded operating point ÷ required output speed. Compare the calculated target with available stage-specific ratios and check allowable continuous load in the selected Datasheet. The resulting number is a screening value, not proof of a tested application.

3. Compare Continuous and Peak Torque Separately

Rated allowable torque supports preliminary continuous-duty screening. Maximum momentary torque is not a continuous rating and does not establish peak duration or frequency. Stage, ratio, motor input and efficiency must be reviewed for the actual configuration.

4. Check the Full Mechanical Interface

Review outside diameter, stage-dependent body length, output shaft and radial/axial load, mounting holes, locating pilot, input pinion and total motor + gearbox assembly length. Output torque alone does not qualify a cantilevered shaft or pulley.

5. Validate Backlash, Holding, Noise and Environment

A published backlash value does not mean zero backlash or guarantee system positioning accuracy. Check application-specific holding behavior, noise, humidity, temperature, lubrication and lifetime in engineering review.

6. Use the Correct CAD

The Original Full Assembly STEP in the table is a public preliminary CAD reference; a separate simplified 4-stage STEP is also available from the release center. A 4-stage simplified reference is not interchangeable with a 1-, 2- or 3-stage production configuration. Confirm the final ratio/stage, motor interface and controlled drawing.

Full / Simplified STEP Files All 32 Application Guides

What to Send for a First Review

A motor drawing or mechanism sketch, target output speed, available space, mounting/shaft needs, continuous and peak load if known, plus prototype quantity and annual estimate if available. Missing details can be reviewed with SigGear engineering.

Send My Motor for Review Send Drawing / STEP / Sample

Luffy · Sales Engineer, SigGear — wangwanrong@siggear.com