Skip to content

42 mm Precision Planetary Gearhead Datasheet (42P)

Status: Public engineering evaluation reference
Release date: 2026-10-08

Input-speed policy revised: 2026-11-19. Permissible input speed is evaluated with the selected motor and gearhead configuration.

The SigGear 42P is a 42 mm planetary gearhead platform with one- to four-stage configurations. Performance values below are consolidated from the current canonical product page. Mechanical-interface details are linked to the controlled 2D drawing reference released for this model.

Key Specifications

Parameter Public value
Nominal outer diameter 42 mm
Number of stages 1-4
gearhead length range 35.6–69.5 mm
Reduction ratio range 3.8:1–660.7:1
Rated allowable torque range 7845.3–14710.0 mN·m
Maximum momentary torque range 15690.6–29420.0 mN·m
Efficiency range 66–90%
Backlash at no load ≤ 1.2°
Continuous permissible input speed Motor/configuration dependent; confirm selected operating point
Operating temperature range −40 to 120 °C
Housing material Steel
Gear material Steel
Output bearing Ball bearings

Maximum momentary torque is not a continuous working rating.

Stage, Ratio and Performance

Stages Gearbox body length L Available ratios Rated allowable torque Maximum momentary torque Efficiency
1 35.6 mm 3.8 / 4.3 / 5.1 7845.3 mN·m 15690.6 mN·m 90%
2 46.9 mm 14.4 / 16.3 / 18.6 / 19.2 / 21.8 / 25.7 9806.6 mN·m 19613.3 mN·m 80%
3 58.2 mm 54.4 / 61.9 / 70.4 / 72.8 / 80.1 / 82.8 / 94.2 / 97.4 / 110.8 / 130.3 11768.0 mN·m 23536.0 mN·m 73%
4 69.5 mm 206.4 / 234.6 / 266.8 / 276 / 303.5 / 313.9 / 345 / 357 / 369.2 / 406 / 419.9 / 477.5 / 493.93 / 561.70 / 660.7 14710.0 mN·m 29420.0 mN·m 66%

Published Load / Shaft Limits

Parameter Public value
Radial load, 10 mm from flange ≤ 16.0 kgf
Shaft axial load ≤ 8.0 kgf
Radial play of shaft ≤ 0.04 mm
Thrust play of shaft ≤ 0.3 mm

These values are taken from the current 42P specification sheet. Application suitability still depends on the actual load direction, duty cycle, stage / ratio, motor operating point and installation.

Motor Matching Reference

  • Adapted DC motor nominal voltage: 3–48 VDC
  • Adapted DC motor power: below 200 W

These are motor-matching conditions, not electrical ratings of the mechanical gearhead.

Mechanical Interface and CAD

View 42P Mechanical Interface v1.0

A simplified public 4-stage STEP reference is released for early packaging and mechanical Design-In. The full assembly STEP is included in SigGear's public release scope. The original assembly source has been identified; its public download will be activated after binary upload and revision verification.

For final CAD, provide the selected ratio, stage count and motor interface.

View 2D Drawing & Full Assembly Release Status

Selection Information Required

Please provide:

  • Required output speed or reduction ratio
  • Continuous and momentary output torque
  • Motor voltage, power and speed
  • Motor shaft diameter and length
  • Motor mounting-hole pattern and locating pilot
  • Output-shaft requirements
  • Radial and axial loads
  • Duty cycle and ambient temperature
  • Backlash, noise and service-life targets
  • Prototype and annual quantity

View 42P Product Page

Engineering Contact

Wanrong Wang
International Sales / Sales Engineer, SigGear
wangwanrong@siggear.com