Integrated Robot Joint Actuator vs Motor + Gearhead¶
A robotics team may choose either an integrated robot joint actuator or a separate motor + gearhead architecture. The better starting point depends on how much of the motor, controller, encoder, mechanical interface and joint packaging is already fixed.
SigGear supports both paths: published robot joint actuator platforms and 8–42 mm planetary gearheads that can be evaluated with an existing or selected motor.
Quick Decision Guide¶
| Project situation | Practical starting point |
|---|---|
| Motor, driver and control stack are already selected | Gearhead-only or motor + gearhead integration review |
| Team wants a compact joint package with motor, transmission and feedback reviewed together | Integrated actuator reference |
| Existing mechanism fixes the motor shaft and mounting pattern | Gearhead / motor-interface review |
| Joint envelope, torque and speed are known but electronics are open | Compare integrated actuator and separate architecture |
| Prototype needs fast mechanical packaging with public CAD | Start from the closest released product platform |
| Production design needs a special shaft, flange, cable or ratio | Project-specific engineering review |
This is a screening guide only. Final selection depends on the complete operating condition.
Integrated Robot Joint Actuator¶
An integrated actuator can combine several functions in one joint package, depending on the selected model and configuration:
- motor
- reducer / gearbox
- encoder or feedback device
- output bearing structure
- driver where applicable
- cable / connector arrangement
- joint-side mechanical interfaces
Potential advantages¶
- fewer separate mechanical interfaces to define
- compact packaging around one known joint envelope
- easier early CAD integration when a released STEP model is available
- motor, reducer and feedback can be reviewed as one system
Items still requiring confirmation¶
- continuous and peak torque
- peak duration
- rated and maximum speed
- driver and encoder version
- communication interface
- brake or power-off behavior
- external loads
- thermal condition
- connector and cable configuration
Do not assume that every integrated actuator includes the same driver, encoder or communication protocol.
Browse SigGear Robot Joint Actuators
Separate Motor + Gearhead Architecture¶
A separate architecture may be preferred when the robotics team already controls the motor, electronics or mechanical design.
Typical starting conditions include:
- an existing BLDC, DC or other motor must be retained
- the controller and encoder architecture are already fixed
- only the reduction stage needs to change
- the gearbox must fit an existing motor shaft and pilot
- the output shaft or flange is application-specific
- a smaller transmission is needed for a hand, gripper or auxiliary mechanism
SigGear publishes 8P–42P planetary gearhead platforms with public datasheets and CAD resources.
Browse 8–42 mm Planetary Gearheads Motor + Gearhead Integration
If You Already Have a Motor¶
Send:
- motor model or drawing
- nominal voltage
- rated / no-load speed
- shaft diameter and usable length
- mounting-hole pattern
- locating pilot
- required output speed
- continuous and peak torque / load
- maximum diameter and total assembly length
A preliminary ratio may be estimated from motor speed divided by target output speed, but the final configuration also needs stage availability, torque, efficiency, duty cycle and motor operating point.
Custom Planetary Gearhead for an Existing Motor
Compare the Complete Joint, Not Only the Reducer¶
When comparing an integrated actuator with a separate motor + gearhead, use the same boundary conditions:
| Category | Compare |
|---|---|
| Mechanics | complete diameter, thickness, length, weight, shaft / flange and mounting |
| Performance | continuous torque, peak torque + duration, speed and duty cycle |
| Loads | radial, axial and overturning loads |
| Precision | backlash, accuracy, repeatability and encoder resolution |
| Electrical | voltage, current limits, motor operating point and regenerative behavior |
| Control | driver location, control mode and communication |
| Thermal | housing, mounting material, enclosure and cooling path |
| Service | replaceable subassemblies, cable access and maintenance strategy |
| Production | prototype quantity, customization scope and design freeze |
SigGear Public Engineering Resources¶
For standard robot joint products:
Robot Joint Datasheets, 2D & STEP
For separate planetary gearheads:
12 Gearhead Datasheets, 2D & STEP
What to Send First¶
You do not need to decide the architecture before contacting SigGear.
Send the joint or mechanism requirement, existing motor / controller information if any, target torque, speed, installation envelope and prototype quantity. The first review can determine whether an integrated actuator, motor + gearhead assembly or gearbox-only path is more appropriate to evaluate.
Robot Joint Actuator Selection Guide Request Engineering Review
Contact: Wanrong Wang · International Sales / Sales Engineer, SigGear · wangwanrong@siggear.com